Skip to main content

WeatherTRAK® ET Pro3®

Smart Irrigation, Perfect Landscape

WeatherTRAK ET Pro3® is the hands-down most tested and proven commercial-grade smart irrigation controller on the market today. This proven controller is EPA WaterSense certified and passed the Irrigation Association’s Smart Water Application Technologies (SWAT) protocol with a perfect score. The ET Pro3 can control a single site or an entire portfolio of sites using conventional wire technology or advanced 2-wire technology.

The WeatherTRAK ET Pro3 smart irrigation controller uses ET Everywhere®, the most precise, high-resolution weather data available, to create specific schedules. All-inclusive options available, which include subscription and warranty for ten years.

With its proven ability to tune irrigation to your unique landscape and site characteristics, the WeatherTRAK ET Pro3 controller reduces water waste by only irrigating when it is necessary – saving you time, resources, and money.

Get more done in less time with WeatherTRAK Central programming and management

Real-time flow alerts make every site and schedule perform more efficiently

Speed up wet checks, troubleshooting, and installs with WeatherTRAK Mobile

ET Pro3 Conventional

  • Support for 12 to 96 stations
  • Six station modularity
  • Five-year warranty
  • Worry-free Wireless Warranty covers cellular technology upgrades

ET Pro3 2-Wire

  • Supports up to 96 stations in standard mode
  • Supports up to 200 stations when upgraded to OptiFlow
  • Five-year warranty
  • Worry-free Wireless Warranty covers cellular technology upgrades

Features

Programming

  • Eight simultaneous programs with five program modes and two start times
  • Program all settings at controller, or remotely
  • Independent station programming (72 cycles/ station) with automated cycle and soak
  • User-defined water days and water windows per program to comply with agency regulations
  • Built-in WeatherTRAK Scheduling Engine optimizes by plant, soil, sprinkler, sun exposure, and slope data
  • Automated daily runtime adjustments using site-specific ET Everywhere weather data
  • Percent adjust to enable fine-tuning by station
  • Automated skip days based on zone-specific soil moisture depletion
  • Runtime rationing protects plant health under constricted water windows
  • Stacked station manual watering from 1-99 minutes

Hardware

  • Integrated flow sensor support included
  • Dedicated master valve and pump start
  • Commercial-grade screw-less wire terminals
  • Built-in amp meter for fault protection and diagnostics
  • Cellular radio and first year of WeatherTRAK Central service included
  • LTE cellular communication for the best coverage and performance
  • 32-pin connector for hardware remote like the TRC Commander and Irritrol® ProMax™ (ET Pro3 Conventional only)
  • New features and firmware pushed over-the-air using WeatherTRAK Cloud Update
  • Share one rain sensor across multiple controllers with RainShare™
  • Robust built-in surge protection integrated directly into the controller

Integrated Flow

  • Mainline/catastrophic break detection and shutdown
  • Real-time station-specific flow monitoring and control
  • Local and remote station-learned flow
  • Fault detection, diagnostics, and alerts
  • Supports up to four flow sensor inputs and master valve outputs
  • Supports normally open or normally closed master valves
  • Customizable flow alert thresholds
  • Upgradable to OptiFlow® for advanced flow management and multi-controller automatic scheduling
  • Supports Data Industrial®, CST, Netafim™ flow sensors and custom “K and offset” values
  • Compatible with WeatherTRAK FlowLink®, FlowShare, Flow3, and FlowHD

2-Wire Exclusive

The HydroPoint H2O platform leverages the industry’s most dynamic 2-Wire technology to provide a powerful solution for smart controllers, valve decoders, and accessories. The system includes:

  • Smart controllers capable of flow management, real-time alerts, and cloud-based control
  • Valve decoders with bi-directional communication, multi-valve management, and built-in LEDs
  • Accessories that enable control over master valves, flow sensor data, and pump start relays
  • Supports up to 4 master valves and 4 flow sensors using direct connect terminals and/or 2-wire decoders

Models

ET Pro3 (CWM)

12 – 48 Station
Conventional Wiring
WALL MOUNT: Cold-Rolled Steel

18-gauge, powder-coated, cold-rolled steel, wall mount enclosure with key-lock entry.

ET Pro3 (CWM)

72 & 96 Station
Conventional Wiring
WALL MOUNT: Cold-Rolled Steel

18-gauge, powder-coated, cold-rolled steel, wall mount enclosure with key-lock entry. Two separate enclosures.

ET Pro3 2-Wire (CWM)

48 & 96 Station
WALL MOUNT: Cold-Rolled Steel

18-gauge, powder-coated, cold-rolled steel, wall mount enclosure with key-lock entry. Station valve decoders not included.

Cold-Rolled Steel Pedestal

Sub-assembly for Pedestal Conversion

16-gauge, powder-coated, cold-rolled steel pedestal enclosure w/ key-lock entry. Controller sold separately.

ET Pro3 (SWM)

12 – 48 Station
Conventional Wiring
WALL MOUNT: Stainless Steel

18-gauge, stainless steel, wall mount enclosure w/ key-lock entry.

ET Pro3 (SWM)

72 & 96 Station
Conventional Wiring
WALL MOUNT: Stainless Steel

18-gauge, stainless steel, wall mount enclosure w/ key-lock entry. Two separate enclosures.

ET Pro3 2-Wire (SWM)

48 & 96 Station
WALL MOUNT: Stainless Steel

18-gauge, stainless steel, wall mount enclosure w/ key-lock entry. Station valve decoders not included.

Stainless Steel Pedestal

Sub-assembly for Pedestal Conversion

16-gauge, stainless steel, pedestal enclosure w/ key-lock entry. Controller sold separately.

Enclosures

ET Pro3 (SPH)

12 – 48 Station
Conventional Wiring
Heavy-Duty, Front-Entry Stainless Steel Controller

Includes control panel, antenna, and terminal boards pre-installed

14-gauge stainless steel, NEMA 3R rated front-entry enclosure w/ key-lock entry. VIT Strongbox enclosure model
no. SB-18SS.

ET Pro3 2-Wire (SPH)

48 & 96 Station
Heavy-Duty, Front-Entry Stainless Steel Controller

Includes control panel, antenna, and terminal boards pre-installed

14-gauge stainless steel, NEMA 3R rated front-entry enclosure w/ key-lock entry. VIT Strongbox enclosure model
no. SB-18SS. Station valve decoders not included.

ET Pro3 (SPT)

12 – 48 Station
Conventional Wiring
Includes control panel, antenna, and terminal boards pre-installed

14-gauge stainless steel, NEMA 3R rated slope-top, top-entry enclosure w/ key-lock entry to upper and lower compartments. VIT Strongbox Enclosure model no. SB-16SS.

ET Pro3 2-Wire (SPT)

48 & 96 Station
Heavy-Duty, Slope-Top, Top-Entry Stainless Steel Controller

Includes control panel, antenna, and terminal boards pre-installed

14-gauge stainless steel, NEMA 3R rated slope-top, top-entry enclosure w/ key-lock entry to upper and lower compartments. VIT Strongbox Enclosure model no. SB-16SS. Station valve decoders not included.

ET Pro3 (SPS)

12 – 48 Station
Conventional Wiring
Light-Duty, Front-Entry Stainless Steel Controller

Includes control panel, antenna, and terminal boards pre-installed

16-gauge stainless steel, NEMA 3R rated front-entry enclosure w/ key-lock entry. VIT Strongbox Enclosure model
no. LD-16S.

ET Pro3 2-Wire (SPS)

48 & 96 Station
Light-Duty, Front-Entry Stainless Steel Controller

Includes control panel, antenna, and terminal boards pre-installed

16-gauge stainless steel, NEMA 3R rated front-entry enclosure w/ key-lock entry. VIT Strongbox Enclosure model
no. LD-16S. Station valve decoders not included.

ET Pro3 (STW)

72 & 96 Station
Conventional Wiring
High Station Count, Heavy-Duty, Slope-Top, Top-Entry Stainless Steel Controller

Includes control panel, antenna, and terminal boards pre-installed

14-gauge stainless steel, NEMA 3R rated top entry enclosure w/ key lock entry. Available in 72 and 96 station counts.

Chassis

ET Pro3 (Chassis 1)

12 – 48 Station Conventional Wiring
Chassis for Wall Mount Enclosure

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any wall mount enclosure 18”w x 18”h x 10”d or larger. (e.g., VIT Strongbox Enclosure Pedestal LD-18SW series). Pancake LTE Antenna included.

ET Pro3 (Chassis 1)

72 & 96 Station Conventional Wiring
Chassis for Wall Mount Enclosure

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any wall mount enclosure 18”w x 18”h x 10”d or larger. (e.g., VIT Strongbox Enclosure Pedestal LD-18SW series). Pancake LTE Antenna included. Two separate units.

ET Pro3 2-Wire (Chassis 1)

48 & 96 Station
Chassis for Wall Mount Enclosure

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any wall mount enclosure 18”w x 18”h x 10”d or larger.

(e.g., VIT Strongbox Enclosure Pedestal LD-18SW series). Pancake LTE Antenna included. Station valve decoder not included.

ET Pro3 (Chassis 2)

12 – 48 Station Conventional Wiring
Chassis for Heavy-Duty Front-Entry Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any heavy-duty front-entry pedestal 18” w x 36” h x 12” d or larger. (e.g., VIT Strongbox Enclosure Pedestal SB-18SS, SB-36SS, or SB-18DSS) Fits in WeatherTRAK SPH series enclosures. Pancake LTE Antenna included.

ET Pro3 (Chassis 2)

72 & 96 Station Conventional Wiring
Chassis for Heavy-Duty Front-Entry Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any heavy-duty front-entry pedestal 18” w x 36” h x 12” d or larger. (e.g., VIT Strongbox Enclosure Pedestal SB-18SS, SB-36SS, or SB-18DSS) Fits in WeatherTRAK SPH series enclosures. Pancake LTE Antenna included. Two separate units.

ET Pro3 2-Wire (Chassis 2)

48 & 96 Station
Chassis for Heavy-Duty Front-Entry Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any heavy-duty front entry pedestal 18” w x 36” h x 12” d or larger. (e.g., VIT Strongbox Enclosure Pedestal SB-18SS series) Fits in WeatherTRAK SPH series enclosures. Pancake LTE Antenna included. Station valve decoders not included.

ET Pro3 (Chassis 4)

12 – 48 Station Conventional Wiring
Chassis for Heavy-Duty Slope-Top Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any slope-top, top-entry pedestal 16” x 38” h x 15.5” d or larger. (e.g., VIT Strongbox Enclosure Pedestal SB-16SS series) Fits in WeatherTRAK SPT series enclosures. Pancake LTE Antenna included.

ET Pro3 (Chassis 4)

72 & 96 Station Conventional Wiring
Chassis for Heavy-Duty Slope-Top Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any slope-top, top-entry pedestal 16” x 38” h x 15.5” d or larger. (e.g., VIT Strongbox Enclosure Pedestal SB-16SS series) Fits in WeatherTRAK SPT series enclosures. Pancake LTE Antenna included. Two separate units.

ET Pro3 2-Wire (Chassis 4)

48 & 96 Station
Chassis for Heavy-Duty Slope-Top Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any slope-top, top-entry pedestal 16” x 38” h x 15.5” d or larger. (e.g., VIT Strongbox Enclosure Pedestal SB-16SS series) Fits in WeatherTRAK SPT series enclosures. Pancake LTE Antenna included. Station valve decoders not included.

ET Pro3 (Chassis 5)

12 – 48 Station Conventional Wiring
Chassis for Light-Duty Front-Entry Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any front-entry pedestal 16.75” w x 30” h x 8.25” d or larger. (e.g., VIT Strongbox Enclosure Pedestal LD-16S series) Fits in WeatherTRAK SPS series enclosures. Pancake LTE Antenna included.

ET Pro3 (Chassis 5)

72 & 96 Station Conventional Wiring
Chassis for Light-Duty Front-Entry Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any front-entry pedestal 16.75” w x 30” h x 8.25” d or larger. (e.g., VIT Strongbox Enclosure Pedestal LD-16S series) Fits in WeatherTRAK SPS series enclosures. Pancake LTE Antenna included. Two separate units.

ET Pro3 2-Wire (Chassis 5)

48 & 96 Station
Chassis for Light-Duty Front-Entry Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into any front-entry pedestal 16.75” w x 30” h x 8.25” d or larger. (e.g., VIT Strongbox Enclosure Pedestal LD-16S series) Fits in WeatherTRAK SPS series enclosures. Pancake LTE Antenna included. Station valve decoders not included.

ET Pro3 (Chassis 7)

12 – 48 Station Conventional Wiring
Chassis for Rain Bird® Maxicom® Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into Rain Bird® Maxicom® ESP-Sat stainless steel enclosure. Pancake LTE Antenna included.

ET Pro3 (Chassis 7)

72 & 96 Station Conventional Wiring
Chassis for Rain Bird® Maxicom® Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into Rain Bird® Maxicom® ESP-Sat stainless steel enclosure. Pancake LTE Antenna included. Two separate units.

ET Pro3 2-Wire (Chassis 7)

48 & 96 Station
Chassis for Rain Bird® Maxicom® Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into Rain Bird® Maxicom® ESP-Sat stainless steel enclosure. Pancake LTE Antenna included. Station valve decoders not included.

ET Pro3 (Chassis 8)

12 – 96 Station Conventional Wiring
Chassis for Heavy-Duty Slope-Top Wide Pedestal

18-gauge anodized, pre-assembled, aluminum back panel retrofits into wide slope-top pedestal 24”w x 30”h x 38”d or larger. (e.g., Strongbox Enclosure Pedestal SB-22SS) Fits in WeatherTRAK STW series enclosures. Pancake LTE Antenna included.

WeatherTRAK Delivers Results

Specifications

ET Pro3 Conventional

Electrical & Enclosure Specifications

Input Power:120 VAC +/- 10%, (60 Hz) or 220 VAC +/- 10%, (60 Hz)
Output Power:24 VAC (60 Hz)1.0 Amp (1000mA) max per station output including a pump start1.0 Amp (1000mA) max per master valve output3.0 Amps (80 VA) total loadUp to 17 terminal outputs energized simultaneously (8 stations, 1 manual, 4 pump starts, 4 master valves)
Consumptive Power:Idle State: 2.5 Watts Power
Maximum Power Requirements for Irrigation State: 70 Watts
Certifications:EPA WaterSense Approved, FCC Certified, UL Listed, 100% SWAT-tested
Enclosure Options:Wall Mount Enclosures16 gauge wall mount enclosure available in stainless and powder coated finishesKey-hole mounting for wall mount enclosures for easy installationEasily adapts to a small 14 gauge pedestal; available in two finishes
VIT Strong Box Stainless SteelPedestal EnclosuresRetrofit Chassis for Existing EnclosuresAll come with key lock entryNEMA-3R weather-resistant

ET Pro3 2-Wire

Electrical & Enclosure Specifications

Input Power:120 VAC +/- 10%, (60 Hz) or 220 VAC +/- 10%, (60 Hz)
Output Power:Station Valve: 24VAC up to 600mA max including a pump startMaster Valve: 24VAC Valves up to 900mAFlow Sensor: Loop Current 4mA, 0-200HzTotal Load: 3.0 Amps (80VA)Up to 17 terminal outputs energized simultaneously (8 stations, 4 manual, 4 pump starts, 4 master valves)
Consumptive Power:Idle State: 3 Watts Power
Maximum Power Requirements for Irrigation State: 70 Watts
Certifications:EPA WaterSense Approved, FCC Certified, UL Listed, 100% SWAT-tested
Enclosure Options:Wall Mount Enclosures16 gauge wall mount enclosure available in stainless and powder coated finishesKey-hole mounting for wall mount enclosures for easy installationEasily adapts to a small 14 gauge pedestal; available in two finishes
VIT Strong Box Stainless SteelPedestal EnclosuresRetrofit Chassis for Existing EnclosuresAll come with key lock entryNEMA-3R weather-resistant
Compatible Wire Options:Coleman Cables #51452Paige Electric P7072D, P7296D, P7350D,
and P7354DRegency 14/2 and 12/2 Maxi CableToro Decoder CableHunter Decoder Jacketed Service Wire
DEC12/2BE and DEC14/2BE

2-Wire Decoders

Single Station Valve Decoder

WeatherTRAK H2O 2-Wire single station valve decoder. Includes four 3MTM DBR/Y-6 splice kits. Available pre-programmed.

Two Station Valve Decoder

WeatherTRAK H2O 2-Wire two station valve decoder. Includes six 3MTM DBR/Y-6 splice kits. Available pre-programmed.

Master Valve Decoder

WeatherTRAK H2O 2-Wire master valve decoder. Includes four 3MTM DBR/Y-6 splice kits.

Pump Start Decoder

WeatherTRAK H2O 2-Wire pump start decoder. Includes four 3MTM DBR/Y-6 splice kits.

Flow Sensor Decoder

WeatherTRAK H2O 2-Wire flow sensor decoder. Includes four 3M™ DBR/Y-6 splice kits. Available pre-programmed.

Surge Arrestor Decoder

WeatherTRAK H2O 2-Wire surge arrestor decoder. Includes four 3M™ DBR/Y-6 splice kits.